Marvel AT Tester V1.1: Simple tool to send AT Commands To Devices Via Comport

Download Marvel AT Tester V1.1 FREE FOR ALL

AT commands are used to control MODEMs. AT is the abbreviation for Attention. These commands come from Hayes commands that were used by the Hayes smart modems. The Hayes commands started with AT to indicate the attention from the MODEM. The dial up and wireless MODEMs (devices that involve machine-to-machine communication) need AT commands to interact with a computer. These include the Hayes command set as a subset, along with other extended AT commands.

AT commands with a GSM/GPRS MODEM or mobile phone can be used to access following information and services:

1. Information and configuration pertaining to mobile device or MODEM and SIM card.

2. SMS services.

3. MMS services.

4. Fax services.

5. Data and Voice link over mobile network.

The Hayes subset commands are called the basic commands and the commands specific to a GSM network are called extended AT commands.

The tool is provide you to use all following command with help of this tool. is a very small utility for all Windows users. i m shared all command below you can easily understand.

What can AT commands be used for?

AT commands enable you to control everything around the modem, device, and SIM:

Wake the device or put it in sleep mode
Configuration of power-saving modes

Scan for and register to available networks and radio types
Get updates about network condition changes
Read/send SMS and USSD
Send data (TCP/IP)
Get hardware and SIM information (IMEI, IMSI, etc.)
and much more

To get started, we will talk about the syntax or the types of AT commands that can be sent to the modem.

List of AT commands:

The AT commands for both, GSM module and the mobile phone, are listed below. Some of these commands may not be supported by all the GSM modules available. Also there might be some commands which won’t be supported by some mobile handsets.

Testing :

Command	Description
AT	Checking communication between the module and computer.

Call control :

Command	Description
ATA	Answer command
ATD	Dial command
ATH	Hang up call
ATL	Monitor speaker loudness
ATM	Monitor speaker mode
ATO	Go on-line
ATP	Set pulse dial as default
ATT	Set tone dial as default
AT+CSTA	Select type of address
AT+CRC	Cellular result codes

Data card Control :

Command	Description
ATI	Identification
ATS	Select an S-register
ATZ	Recall stored profile
AT&F	Restore factory settings
AT&V	View active configuration
AT&W	Store parameters in given profile
AT&Y	Select Set as power up option
AT+CLCK	Facility lock command
AT+COLP	Connected line identification presentation
AT+GCAP	Request complete capabilities list
AT+GMI	Request manufacturer identification
AT+GMM	Request model identification
AT+GMR	Request revision identification
AT+GSN	Request product serial number identification (IMEI)

Phone control :

Command	Description
AT+CBC	Battery charge
AT+CGMI	Request manufacturer identification
AT+CGMM	Request model identification
AT+CGMR	Request revision identification
AT+CGSN	Request product serial number identification
AT+CMEE	Report mobile equipment error
AT+CPAS	Phone activity status
AT+CPBF	Find phone book entries
AT+CPBR	Read phone book entry
AT+CPBS	Select phone book memory storage
AT+CPBW	Write phone book entry
AT+CSCS	Select TE character set
AT+CSQ	Signal quality

Computer data interface :

Command	Description
ATE	Command Echo
ATQ	Result code suppression
ATV	Define response format
ATX	Response range selection
AT&C	Define DCD usage
AT&D	Define DTR usage
AT&K	Select flow control
AT&Q	Define communications mode option
AT&S	Define DSR option
AT+ICF	DTE-DCE character framing
AT+IFC	DTE-DCE Local flow control
AT+IPR	Fixed DTE rate

Service :

Command	Description
AT+CLIP	Calling line identification presentation
AT+CR	Service reporting control
AT+DR	Data compression reporting
AT+ILRR	DTE-DCE local rate reporting

Network Communication parameter :

Command	Description
ATB	Communications standard option
AT+CBST	Select bearer service type
AT+CEER	Extended error report
AT+CRLP	Radio link protocol
AT+DS	Data compression

Miscellaneous :

Command	Description
A/	Re-execute command line
AT?	Command help
AT*C	Start SMS interpreter
AT*T	Enter SMS block mode protocol
AT*V	Activate V.25bis mode
AT*NOKIATEST	Test command
AT+CESP	Enter SMS block mode protocol

SMS Text mode :

Command	Description
AT+CSMS	Select message service
AT+CPMS	Preferred message storage
AT+CMGF	Message format
AT+CSCA	Service centre address
AT+CSMP	Set text mode parameters
AT+CSDH	Show text mode parameters
AT+CSCB	Select cell broadcast message types
AT+CSAS	Save settings
AT+CRES	Restore settings
AT+CNMI	New message indications to TE
AT+CMGL	List messages
AT+CMGR	Read message
AT+CMGS	Send message
AT+CMSS	Send message from storage
AT+CMGW	Write message to memory
AT+CMGD	Delete message